Category

Resistor Wattage Calculator — Power Dissipated by Resistors in Series and Parallel Circuits

Calculate the power dissipated by a resistor from any two of voltage, current, resistance, or power. Analyze series and parallel circuits with up to 10 resistors. Supports metric (SI) and American (BTU/hr) unit systems plus optional electricity cost in 12 currencies.

0 calculations

Calculation Parameters

Enter cost per kWh (e.g. 0.15) to calculate running costs

Enter Parameters

Fill in the form on the left and click "Calculate"

Resistor Wattage Calculator — Find Power Dissipated by Any Resistor

The resistor wattage calculator lets you figure out how much electrical power a resistor absorbs and dissipates as heat. Enter any two known electrical values — voltage, current, resistance, or power — and the calculator instantly finds the remaining two using Ohm's Law and the power formula.

You can also use this tool to analyze series and parallel circuits with up to 10 resistors, finding individual and total power dissipation for each component. An optional electricity cost section shows your running costs in USD, RUB (₽), EUR, GBP, and other major currencies.

How to Determine the Wattage of a Resistor

A resistor's power rating (wattage) tells you the maximum power it can safely dissipate as heat without damage. Common power ratings:

  • 1/20 W (50 mW) — SMD chip resistor 0201 (0.6 × 0.3 mm)
  • 1/8 W (125 mW) — smallest carbon composition resistor
  • 1/4 W (250 mW) — standard through-hole resistor
  • 1/2 W (500 mW) — medium power resistor
  • 1 W — 2512 thick film chip resistor (6.3 × 3.2 mm)
  • 5 W — largest carbon composition resistor

Always choose a resistor whose power rating is at least 2× the calculated dissipation to ensure a safe thermal margin.

What Is the Formula for Electrical Power?

Electric power describes how fast energy is transferred. When current flows through a resistor, the electrical energy converts to heat. The fundamental power formula is:

P = V × I

where:

  • P — power (watts, W)
  • V — voltage across the resistor (volts, V)
  • I — current through the resistor (amperes, A)

Combined with Ohm's Law (V = I × R), we get three equivalent power formulas:

Known valuesPower formula
Voltage (V) + Current (I)P = V × I
Voltage (V) + Resistance (R)P = V² / R
Current (I) + Resistance (R)P = I² × R

How to Find the Power Dissipated by a Resistor

The power dissipated by a resistor is the rate at which it converts electrical energy into heat. To find it:

  1. Identify which two quantities you know (V, I, R, or P).
  2. Select the matching formula from the table above.
  3. Enter the values into the calculator — it resolves the other two automatically.

Example: A 100 Ω resistor with 12 V across it dissipates P = 12² / 100 = 1.44 W. The current is I = 12 / 100 = 120 mA. You need a resistor rated at at least 3 W (2× safety margin).

How to Use the Resistor Wattage Calculator for Circuits with Multiple Resistors

Switch to Series Circuit or Parallel Circuit mode and enter:

  • Supply voltage — the total voltage applied to the circuit.
  • Number of resistors — 2 to 10 resistors.
  • Resistance values — each resistor's value with its unit (mΩ, Ω, kΩ, MΩ).

The calculator returns for each resistor: its individual voltage drop, current, and power — plus circuit totals.

Series Circuit

In a series circuit, the same current flows through all resistors: I = V / (R₁ + R₂ + … + Rₙ). Power per resistor: P_i = I² × R_i.

Parallel Circuit

In a parallel circuit, the same voltage appears across all resistors: 1/R_total = 1/R₁ + 1/R₂ + … + 1/Rₙ. Power per resistor: P_i = V² / R_i.

Is This Calculator Suitable for Resistors in AC Circuits?

Yes, for purely resistive loads in AC circuits the same DC formulas apply — a resistor's impedance equals its resistance (Z = R, no reactive component). Power factor = 1, so P = V_rms × I_rms = V_rms² / R.

For circuits containing capacitors or inductors, you must account for reactive power and use complex impedance analysis.

Metric vs. American (Imperial) Unit Systems

All electrical units (volt, ampere, ohm, watt) are universally identical in both metric (SI) and American engineering practice. The difference in this calculator is the display of power results:

  • Metric (SI): µW, mW, W, kW — standard SI prefixes.
  • American: W and BTU/hr — 1 W = 3.41214 BTU/hr, used in HVAC and thermal engineering.

Unit prefixes for input values (mΩ / Ω / kΩ / MΩ, mV / V / kV, µA / mA / A / kA) are identical in both systems.

Electricity Cost Calculator

If your resistor runs continuously (e.g., a pull-up resistor or bleeder resistor), enter your local electricity rate (cost per kWh) to see the annual running cost. The calculator supports 12 currencies including USD ($), RUB (₽), EUR (€), GBP, JPY, CNY, BRL, CAD, AUD, CHF, INR, and KRW.

Example: A 1 W resistor running 24/7 consumes 1 W × 24 h × 365 d = 8.76 kWh/year. At $0.15/kWh that's $1.31/year; at ₽6/kWh that's ₽52.56/year.

FAQs

What happens if a resistor exceeds its wattage rating?

Exceeding the power rating causes excessive heating. The resistor may drift in value, crack, burn, or cause a fire. Always choose a power rating with a 2× safety margin, or 1.5× minimum for stable thermal conditions.

How do I read a resistor's power rating?

Through-hole resistors: rated by physical size (1/4 W is ~6 mm long). SMD resistors: rated by package code (0402 = 1/16 W, 0603 = 1/10 W, 0805 = 1/8 W, 1206 = 1/4 W, 2512 = 1 W). Wire-wound and metal oxide resistors may be marked in watts directly.

Can I use this tool for LED current-limiting resistors?

Yes. Enter the voltage across the resistor (supply voltage minus LED forward voltage) and the desired current to find the resistance and power. For example: 5 V supply, 2 V LED forward voltage, 20 mA → R = (5 − 2) / 0.02 = 150 Ω, P = 0.02² × 150 = 60 mW.

Calculation History

Loading...